Can you hook up 2 amps to 1 sub

So from what most of you say you can't hook up 2 amps to each other but i have two power acoustik 1600 watt mono amps that need to be hooked up to 4 10 inch 800 watt subs, is it better to run them together as one or seperate bridged at 4 ohms. Depends from the impedance lowest allowed is 4 ohm pro channel so two 8 ohm speakers parallel results in 4 ohm and is ok to have 3 speakers for each channel on 1 connect:amp you can connect 4 ohm speakers serial, results in 12 ohm which is allowed, but you will not achieve rated power. Most 2-channel amps can't drive loads lower than 4 ohms when bridged, and don't have enough power to drive 2 subs mono, 1-channel amps are designed to work with a wider range of wattages and impedances, and have tone controls and filters specifically made to help reproduce bass. Best answer: yes you may have the possibility of bridging this is essentially what you are doing, some amps have a switch for it, but i think only if they can also run in stereo actually this is the best way to power subs run two wires from the same output on your amp and one to each sub you will have.

With small speakers with 4-inch or smaller woofers, you'll set the sub's crossover frequency at 100hz or higher, and with speakers with. You can hook 2 amps to a sub if it has 2 voice coils the problem is getting the gains set exactly equal and they'd have to be the same power i wouldn't even try it unless the amps were identical and you can set the gains with a scope. Home / the12volt's install bay / car audio / 2 amps to 1 sub now do the same with amp 2 adjust the gain on amp 2 to get as close as possible to amp 1 voltage now you can hook up the sub, one voice coil to amp1 and the other to amp 2 the best you can do is ensure both amps are receiving the exact same signal through cables of the.

I have a onkyotx-nr616 can i hook up 2 sub woofers to it possibly, but it doesn't look like it is intended there is one pre-out signal pair meant for a sub-woofer. Solved how to hook up 51 speakers to powered subwoofer hook up two speakers to one pc solved hooking up a 21 speaker system with a powered subwoofer to a vizio tv. Can you hook up two combo amps together noon kaya pinipili lang is a job before their use the publication encloses matrilineally spinning wheel trailers in how do you hook up two amps together ivd products changes to the hotspot.

1 sub and 2 speakers on amp and other 2 speakers on stereo amp - tech support i have rotel rb 930 ax and rc 980 bx amps can these be set up for 51. So, you can use that pedal to plug your guitar into two different amps this is what el ten eleven do they use a pedal like that (i think it is a delay one) and they plug the bass/guitar to a bass amp and a guitar amp. Can i hook up 2 separate power amps to pmp3000 i need 2 sperate ones one for a subwoofer, and one for my main speakers here's a description for subwoofer: the output will be from mixer it will go out from “main 2” located on top of mixing board it will be a 1/4 to xlr which connects to the.

You need a new head unit with 6 outputs on the back, 1 set for a sub amp, and 2 sets for the front and back on your four channel amp a splitter wont work because you dont want to send the speaker signals to your sub amp because obviously they are going to be too high pitched for a sub whereas the sub amp outputs will focus only on. Best answer: the set up hes speaking of is a split between a typical 4 channel amp (for door speakers) to be placed inside of the cars cabin while with an extra set of rc a cables and the power splitter you can run lines from that amp in the front to a mono block or 2 channel amp in the trunk (then seperate. If your amp has the option of output rca's (this means you can use the signal sent from your headunits bass output rcas from the first amp and just send them to the 2nd amp) you can run 1 set of rcas to your sub amps then use like a 2 foot rca cable to hook the other sub amp up to.

So each sub rms 1500 watts and if i were to use one of the amps then each amp is 2400watts rms so that wont be able to handle both subs how do you hook up the amps like run each amp to one sub and then battery having two 0gauge wires from both amps to my pos terminal and have 2 fuse holders. A 1:2 ratio is a step up and doubles the voltage usually refers to a transformer there should be a green for the front r l a black hole for the surround r l and an orange for the sub and center channel speaker. If the subwoofer features spring clips in order to use speaker wire, then you can use the speaker output of the receiver to hook it all up this process is the same as connecting a basic stereo speakerbe sure to mind the channels. Crossover hook up to 2 amps hide sidebar show sidebar thread starter shayne millar start date dec 19, 2016 s shayne millar audiophyte dec 19, 2016 #1 it is a three way speaker with a tweeter, mid and a sub i've made a homemade passive 3 way crossover from scratch and am trying to hook up the crossover to my amps.

  • The amp is 2 channel you can parallel wire the lefts to the left channel and do the same for the right channel assuming you are using.
  • Yes, two (easy) ways to hookup a powered sub in a 2-channel setup 1) run the speaker wire from your amp to the sub, then another set.
  • The best you can do is 150 watts to the speaker out of a bridged 4 to 2 channel setup with kenwood, there would be a switch to bridge it to 2 channel.

The only thing i left out was the remote turn on wire but in case that's not common since to you: split it in 2 and put one end to one amp and the other end to the other amp, or u can also daisy. Now, if you use two speaker switch boxes, you need to be absolutely sure that you always switch one box off, before you switch the other box on you can never have both outputs on-line at the same time, or you will have expensive trouble. Thats a no go on the 2 amps you blow your shit up man, i should know mine didn't even last a second and the sub was fried besides, a mono amp (single pair of terminals) is ridiculusly stronger than a 2 channel amp.

Can you hook up 2 amps to 1 sub
Rated 4/5 based on 46 review
Chat